Richmond Water Heater Temperature Adjustment [All Heater Types]

This is a complete guide on Richmond Water Heater Temperature Adjustment will describe: 

• How to adjust the Richmond Tankless Water Heater?
• How to adjust the temperature on an electric water heater?
• How to adjust the gas water heater temperature?

Table of Contents

• Richmond Water Heater Temperature Adjustment [All Heater Types]
  • Adjusting Tankless Water Heater Temperature: 
  • Adjusting Electric Water Heater Temperature:
  • Adjusting Gas Water Heater Temperature: 
• Do Richmond Water Heaters Have Heat Traps? 
• How Long Does It Take For A Richmond Water Heater To Heat Up? 

Richmond Water Heater Temperature Adjustment [All Heater Types]

From this chapter, you will learn how to adjust temperature on a Richmond Water Heater, regardless of their types. 

Adjusting Tankless Water Heater Temperature:

Adjusting the temperature on a Richmond Tankless Water Heater is simple. Go along with the following steps to adjust the temperature:

• Turn on the water heater by pressing the On/off button.
• Press the Up button on the control panel to increase the water temperature. 
• To decrease the temperature, press the Down button. 

However, if you want to adjust the set temperature above 120°F, follow the below steps: 

• Turn on the control by pressing the On/Off button.
• Turn off the gas and water supply to the water heater by closing the shut-off valves.
• Press the Up adjustment button continuously until the 120°F shows in the LED display. 
• Press and hold down the Up adjustment button for 5 seconds while 120°F is shown on the LED display.

To disable the set temperature above 120°F, try these steps: 

• Press the down button until 100 appears
• Press and hold the Down button for 2 seconds. At the same time, press the Up button. 

Adjusting Electric Water Heater Temperature:

On the Richmond Electric Water Heater, you can adjust the temperature by turning the thermostat dial pointer, which you can find behind the jacket access panel. Try the following steps to adjust the temperature on Richmond Electric Water heater: 

• Turn off the electric supply to the unit at the circuit breaker.
• Unscrew the jacket access panel and take out it. Then, remove the insulation, which will expose the thermostat. 
• Use a small screwdriver to set the thermostat dial pointer to the desired temperature setting. 
• Replace the insulation and the jacket access panel. 
• Restore power to the water heater. 

Adjusting Gas Water Heater Temperature: 

You can adjust the gas water heater temperature by turning the thermostat knob on the gas control valve. The thermostat knob has several water temperature settings, including: 

• Low: It represents a balmy water temperature around 91°F. 
• Hot: The approximate water temperature of this setting is around 125°F. 
• A: It signifies a water temperature of around 130°F.
• B: This temperature setting will give you approximately a water temperature of 140°F.
• C: It gives you a water temperature of 150°F. 
• Very Hot: “Very Hot” indicates a water temperature of approximately 155°F.

Turn the thermostat knob on the gas control valve to Hot or any temperature setting to set or finalize the output water temperature. 

Do Richmond Water Heaters Have Heat Traps?

Yes, Richmond Water Heaters have heat traps, but they are optional. A heat trap on the water heater is a flap or loop of pipe that prevents heat from escaping the tank. It’s installed on the cold water inlet and hot water outlet pipes on the water heater. The heat traps let the cold water flow into the tank but prevent the heated water from flowing out of the tank. They help reduce convective heat loss. 

How Long Does It Take For A Richmond Water Heater To Heat Up?

It depends on the type of water heater. For example, a water heater will take 30-120 minutes to heat the water after resetting. A gas water heater will take 30-40 minutes to fully heat up. On the other hand, an electric water heater will take an hour or two to heat up. However, a newly installed electric water heater will take several hours to reach the normal operating temperature. Keep in mind; sediment buildup at the bottom of the tank affects the reheating time. 

Discover:

• Richmond Water Heater Troubleshooting
• Richmond Electric Water Heater Troubleshooting