State Select Water Heater Igniter Replacement [Ultimate Guide]
This guide on State Select Water Heater Igniter Replacement will break down:
- How do you replace the igniter on the State Select Water Heater?
- How much does it cost to replace the igniter?
So, let’s dive in.
Table of Contents
- State Select Water Heater Igniter Replacement [7 Easy Steps]
- How Much Does It Cost To Replace A Water Heater Igniter?
- FAQs
- End-Note
State Select Water Heater Igniter Replacement [7 Easy Steps]
The igniter on every gas tank water heater is responsible for igniting the gas. If it gets defective, you won’t ignite the unit to get hot water.
To ignite your water heater, you must replace the igniter with a new one.
And here, I will take you through a step-by-step guide to make that replacement like a pro.
1. Set the temperature dial on the gas control thermostat to its lowest setting.
2. Turn the gas control knob to the Off position.
3. Turn off the gas supply to the unit by turning the manual gas shut-off valve. The gas shut-off valve should be perpendicular on the gas line.
4. Disconnect the igniter wire attached to the igniter.
5. Now, it’s time to take the igniter off. In this case, just slide the ¼” flat head screwdriver behind the top of the igniter bracket. Then, push the screwdriver gently to let the igniter hang freely off to the side of the water heater.
6. To install the new igniter, align the bracket on the gas valve and push forward to snap it into place.
7. Attach the spark igniter wire to complete the installation. Now, your water heater should be ready for use.
How Much Does It Cost To Replace A Water Heater Igniter?
Generally, it will cost you between $70 to $350 to replace the water heater igniter professionally, depending on the location you live.
However, the part itself will cost you only $10 to $20.
I highly recommend you make the replacement for yourself. Just follow the step-by-step procedure I mentioned above and get the igniter replaced.
In this way, you can save up to $100.
FAQs
Why does my hot water heater igniter not ignite?
Your hot water heater igniter won’t igniter if its wiring comes loose from the igniter or the igniter itself goes bad. That’s why it will be better to inspect the spark igniter wiring. If it comes loose, reattach the wiring.
If re-attaching the igniter wiring doesn’t bring any luck, I bet the igniter gets defective. In this case, you need to replace the igniter with a new one.
Can you manually light a water heater with electric ignition?
Yes, you can manually light a water heater with the electric ignition or the igniter. Just press the gas control knob all the way in and keep depressing the igniter button until the pilot light comes on.
How do you light a State Select Water Heater?
Go along with the following steps to light the State Select Water Heater:
- Turn the manual gas shut-off valve to the On position.
- Remove the outer cover and set the thermostat to its lowest setting. Keep turning the thermostat dial fully clockwise until it stops.
- Set the gas control knob to Pilot by turning it counterclockwise.
- Push the gas control knob all the way in and keep depressing the igniter button until the pilot light comes on.
- Once the pilot light comes on, release the igniter button immediately and set the gas control knob to your desired temperature setting.
Note: If the pilot light doesn’t come on after two attempts, turn the gas supply off and call a certified plumber.
End-Note
Replacing the igniter on your State Select Water Heater is just a piece of cake. What you need to do is- just follow the 7 easy steps and have your igniter replaced successfully. Happy Plumbing!
<
strong>Read Also:Eric Alvarez is the head of content on LilDutchUncle.Com. He is an HVAC guy based in El Paso, Texas, United States. He obtained his Bachelor of Science degree from the University Of Texas at El Paso. Years of experience in the HVAC field have taught him many lessons, not the least of which is that the value of quality and knowledge far exceeds any promised initial savings. He has a good standing reputation for superior skills in heating, air conditioning, hot water tanks, and indoor air quality systems.
